Composite Plate Bending Analysis With Matlab Code 〈Verified Source〉

dx2 = dx^2; dy2 = dy^2; kxx = (w(i_center-1,j_center) - 2 w(i_center,j_center) + w(i_center+1,j_center)) / dx2; kyy = (w(i_center,j_center-1) - 2 w(i_center,j_center) + w(i_center,j_center+1)) / dy2; kxy = (w(i_center-1,j_center-1) - w(i_center-1,j_center+1) - w(i_center+1,j_center-1) + w(i_center+1,j_center+1)) / (4 dx dy);

% Interior points for i = 3:Nx-2 for j = 3:Ny-2 n = idx(i,j); % w_xxxx K(n, idx(i-2,j)) = K(n, idx(i-2,j)) + c1; K(n, idx(i-1,j)) = K(n, idx(i-1,j)) - 4 c1; K(n, idx(i,j)) = K(n, idx(i,j)) + 6 c1; K(n, idx(i+1,j)) = K(n, idx(i+1,j)) - 4 c1; K(n, idx(i+2,j)) = K(n, idx(i+2,j)) + c1; % w_yyyy K(n, idx(i,j-2)) = K(n, idx(i,j-2)) + c3; K(n, idx(i,j-1)) = K(n, idx(i,j-1)) - 4 c3; K(n, idx(i,j)) = K(n, idx(i,j)) + 6 c3; K(n, idx(i,j+1)) = K(n, idx(i,j+1)) - 4 c3; K(n, idx(i,j+2)) = K(n, idx(i,j+2)) + c3; % w_xxyy K(n, idx(i-1,j-1)) = K(n, idx(i-1,j-1)) + c2; K(n, idx(i-1,j)) = K(n, idx(i-1,j)) - 2 c2; K(n, idx(i-1,j+1)) = K(n, idx(i-1,j+1)) + c2; K(n, idx(i,j-1)) = K(n, idx(i,j-1)) - 2 c2; K(n, idx(i,j)) = K(n, idx(i,j)) + 4 c2; K(n, idx(i,j+1)) = K(n, idx(i,j+1)) - 2 c2; K(n, idx(i+1,j-1)) = K(n, idx(i+1,j-1)) + c2; K(n, idx(i+1,j)) = K(n, idx(i+1,j)) - 2*c2; K(n, idx(i+1,j+1)) = K(n, idx(i+1,j+1)) + c2; Composite Plate Bending Analysis With Matlab Code

We assemble a sparse linear system ( [K] {w} = {f} ) and solve. Below is the complete code. It computes deflections, curvatures, and then stresses in each ply at Gauss points. dx2 = dx^2; dy2 = dy^2; kxx =

% Apply simply supported boundary conditions: w=0 and Mxx=0 => w,xx=0 on x-edges % We'll set w=0 on all edges and use ghost points to enforce curvature=0 % For simplicity, we set w=0 on boundary nodes and eliminate their equations. % Apply simply supported boundary conditions: w=0 and

%% Composite Plate Bending Analysis Using CLPT & Finite Differences clear; clc; close all; %% Material Properties (T300/5208) E1 = 181e9; % Pa E2 = 10.3e9; G12 = 7.17e9; nu12 = 0.28; nu21 = nu12 * E2/E1;

%% Stress Recovery % Compute curvatures at center element (using central diff) i_center = round(Nx/2); j_center = round(Ny/2); if mod(Nx,2)==0, i_center=i_center+1; end if mod(Ny,2)==0, j_center=j_center+1; end